roger gnss logo web
roger gnss logo web

ROGER GNSS Amplifier&Splitter (GNSS-AS)

GNSS ASROGER GPS Signal Splitter & Amplifier is a combined signal splitter and line amplifier with an output of +16db that can transmit to up to three separate repeater units. The splitter & amplifier is easy to use and permits a wide range of system configurations.

If the signal is to be transmitted to fewer than five or three repeaters, the unused ports should be terminated. Termination should be done with ROGER GPS Terminator 50 Ohm.

Continue Reading

ROGER GNSS Repeater unit (GNSS-L1G1GA-IP67)

GNSS L1G1GA IP67

ROGER GPS/GLONASS/GALILEO repeater operates by receiving satellite signals with an antenna located outside the building and re-radiating the signals to the indoor area or covered space. Use of re-radiated signals indoors means that GPS/GLONASS/GALILEO receiver is tracking the current status and signal from the satellites. When a GPS/GLONASS/GALILEO receiver is moved from covered area to outdoors and vice versa, the receiver is instantly tracking the location instead of time consuming acquisition.

Each ROGER GPS repeater is capable of transmitting the GNSS signal distance up to 40-50 meters from the repeater center. If necessary, the area can be extended by adding additional repeater units, all connected to the same external antenna, using a signal splitter and line amplifier..

Continue Reading

ROGER GNSS Amplifier (GNSS-A-IP67)

GNSS AROGER™ GPS Line Amplifier is an amplifier that is used to allow for longer cable runs and/or signal splitting to several GPS Repeaters.
 
It has a gain of +16dB at the GPS L1,L2 and GLONASS frequency bands and it includes a filter to remove unwanted signals that may have entered the cable at some point.
The amplifier is powered though the output signal cable by the ROGER GPS Repeater and it passes on the DC power for the GPS receiving antenna or another GPS line amplifier.

Continue Reading

ROGER GNSS Amplifier&Splitter (GNSS-AS-IP67)

GNSS ASROGER GPS Signal Splitter & Amplifier is a combined signal splitter and line amplifier with an output of +16db that can transmit to up to three separate repeater units. The splitter & amplifier is easy to use and permits a wide range of system configurations.

If the signal is to be transmitted to fewer than five or three repeaters, the unused ports should be terminated. Termination should be done with ROGER GPS Terminator 50 Ohm.

Continue Reading

ROGER GNSS Splitter 1to2 (GNSS-S2-IP67)

S2With the ROGER™ GPS Signal Splitter, is a signal splitter that is used to distribute GNSS signals to several Repeaters. Splitter works with GPS L1, GPS L2 and GLONASS frequency bands. It has one chaining output and two repeater outputs. DC power is passed on from the chaining output to the input connector for a line amplifier and to a GNSS receiving antenna. ROGER™ GPS Splitter is a one to two signal splitter with an output of -4 dB (2 ports) that can transmit a signal to up to two separate GNSS repeater units.

The splitter is easy to use and permits a wide range
of system configurations.

Continue Reading

ROGER GNSS Splitter 1to5 (GNSS-S-IP67)

S sideWith the ROGER™ GPS Signal Splitter, is a signal splitter that is used to distribute GNSS signals to several Repeaters. Splitter works with GPS L1, GPS L2 and GLONASS frequency bands. It has one chaining output and four repeater outputs. DC power is passed on from the chaining output to the input connector for line amplifier and a GNSS receiving antenna. 

ROGER™ GPS Splitter is a one to five signal splitter with an output of -4 dB (1 port) and -12 dB (4 ports) that can transmit a signal to up to five separate GNSS repeater units.

The splitter is easy to use and permits a wide
range of system configurations.

..

Continue Reading

ROGER GPS Repeater unit (GPSR-1)

GPSR 1 topEach ROGER GPS repeater is capable of transmitting the GPS signal over an area of about 1000 square meters and distance up to 50 meters from the repeater center. If necessary, the area can be extended by adding additional repeater units, all connected to the same external antenna, using a signal splitter and line amplifier. Every repeater unit is supplied with a main power supply unit.

Key Features
• Automatic gain limitation
• Oscillation prevention with indicator
• Maximal coverage for CE approved repeater
• Instant GPS fix when moving outdoors
• Full product family with repeaters, amplifiers and splitters
• Internal transmit antenna

Continue Reading

ROGER GNSS Repeater unit (GNSS-L1G1GA)

GNSS L1G1

The ROGER GPS/GLONASS/GALILEO repeater operates by receiving satellite signals with an antenna located outside the
building and re-radiating the signals to the indoor area or
covered space. Use of re-radiated signals indoors means that GPS/GLONASS/GALILEO receiver is tracking the current status and signal from the satellites. When a GPS/GLONASS/GALILEO receiver is moved from covered area to outdoors and vice versa, the receiver is instantly tracking the location instead of time consuming acquisition.

Each ROGER GPS repeater is capable of transmitting the GNSS signal distance up to 50 meters from the repeater center. If necessary, the area can be extended by adding additional repeater units, all connected to the same external antenna, using a signal splitter and line amplifier.

Continue Reading

ROGER GNSS Amplifier (GNSS-A)

amplifiern.gifROGER™ GPS Line Amplifier is an amplifier that is used to allow for longer cable runs and/or signal splitting to several GPS Repeaters. It has a gain of +16dB at the GPS L1 frequency band and it includes a filter to remove unwanted signals that may have entered the cable at some point.
The amplifier is powered though the output signal cable by the ROGER GPS Repeater and it passes on the DC power for the GPS receiving antenna or another GPS line amplifier.

Continue Reading

ROGER GNSS Amplifier Splitter (GNSS-AS)

ROGER™ GNSS Amplifier & Splitter is a combined signal splitter and line amplifier that can
transmit amplified signal to up to three separate repeater units.


Amplifier has a gain of +16dB and it includes a filter to remove unwanted signals that may have entered the cable at some point.

Splitter is a one to three signal splitter that can transmit signal to up to threGNSS-AS.pnge separate GNSS
(Global Navigation Satellite System) repeater units.

Amplifier is powered through the output signal
cable by the ROGER™ GNSS Repeater and
also passes on DC power for the ROGER™
GNSS Splitter, an another GNSS line amplifier or
GNSS receiving antenna.
The splitter & amplifier is easy to use
and permits a wide range of system
configurations.

 

TECHNICAL SPECIFICATIONS

Amplifier section

Size

110x143x28 mm
Weight 195 g
Operating temperature     -25 - +55°C
Connectors

TNC female input,                TNC female output.

1 x +12 dB with amplifier section     2 x +4 dB with amplifier section

Frequency range 1200-1700 MHz
Noise figure <5dB
Impedance

50Ω

Gain

+16dB

Splitter section
Connectors

TNC female input, 3xTNC female output

1 x -4dB without amplifier sectionwith DC input from repeater.
2 x -12dB without amplifier section and DC blocked for repeaters.

Power supply: The amplifier&splitter is powered through the output / DC input connector
by the ROGER GNSS Repeater
Frequency range: 1200-1700 MHz

ROGER GNSS Splitter 1to2 (GNSS-S2)

With the ROGER™ GPS Signal Splitter, is a signal splitter that is used to distribute

GNSS signals to two Repeaters or to any Roger GNSS equipment. The splitter works with GPS L1, GPS L2 and GLONASS frequency bands. It has one chaining output and two repeater outputs.

DC power is passed from the chaining output to the input connector for line amplifier and to GNSS receiving antenna. ROGER™ GPS Splitter is a one to two signal splitter with an output of -4 dB (2 ports) that can transmit a signal to up to two separate GNSS repeater units.

The splitter is easy to use and permits a wide range of system configurations.

  

Continue Reading

ROGER GNSS Splitter 1to5 (GNSS-S)

ROGERSplitterWith the ROGER GPS Signal Splitter, the signal from one external antenna can be redistributed to up to five repeater units. It is advisable to use a separate amplifier with the signal splitter in order to ensure adequate transmission power to all the five repeaters. If the signal is to be transmitted to fewer than five repeaters, the unused ports should be terminated.

Continue Reading

ROGER GPS Repeater Package (GPSR-BP)

repeaterBp.jpg

A single ROGER GPS Repeater Package is enough to provide a GPS indoor coverage distance up to 50m from the repeater center. Mount the external antenna on the roof of the building and connect the cable supplied with the kit to the antenna and to the repeater installed indoors.

Connect the power supply unit to the repeater, adjust the transmission power of the repeater according to the local conditions, to prevent a signal loopback and indoor GPS coverage is immediately available. 

Several ROGER GPS Repeater Packages can be installed in the same building. Alternatively, the signal coverage provided by a single package can be extended with ROGER GPS Accessories, such as line amplifiers and signal splitters.

What's in the box

  • Outdoor antenna for receiving the GPS signals
  • Antenna mount and adapter for cables
  • ROGER GPSR-1 Repeater unit
  • Power supply
  • RF-cabling, 20 m
  • Manual

ROGER GPS Repeater Package Easy (GPSR-EP)

rogerpackA single ROGER GPS Repeater Package Easy is enough to provide a GPS indoor coverage up to 50m from the repeater center. Mount the patch antenna on the outside of the window and connect the antenna cable, 6 meters.

Connect the power supply unit to the repeater and adjust the transmission power of the repeater according to the local conditions to prevent a signal loopback. Indoor GPS coverage is immediately available. The kit includes clear installation instructions.

Several ROGER GPS Repeater Packages can be installed in the same building. Alternatively, the signal coverage provided by a single package can be extended with ROGER equipment, such as line amplifiers and signal splitters.

Continue Reading

ROGER GNSS Splitter&Amplifier Package (GNSS-L1G1GA-SAP or GPSR-SAP)

rogerpack.gifTo extend the coverage area provided by the ROGER GNSS Repeater Package, use the complete ROGER GNSS Repeater Splitter & Amplifier extension kit that includes cable, 1 line amplifier, 2 repeater units, alternatively with Galileo/GPS/Glonass repeater OR GPS L1 repeater, depending on your needs and a new signal splitter/line amplifier.

Continue Reading

ROGER GPS DC Installation Package (GPSR-DCP)

The ROGER GPS repeater can also be installed in environment with DC power. An on board rogerpackrepeater ensures the trouble-free transmission of the tracking data e.g. in a vehicle and a reliable operation of the GPS devices. The ROGER GPS DC Installation Package contains a repeater unit, a compact and unobtrusive magnetic GPS antenna and a voltage regulator (12V or 24V).

Continue Reading